鑽床的選擇 - 木工
By Olive
at 2012-04-02T09:12
at 2012-04-02T09:12
Table of Contents
為了把洞鑽直，看來鑽床是不二的選擇，所以問問幾個
目前考慮這台 http://goods.ruten.com.tw/item/show?21203234609990
有這台用戶可以分享一下嗎？
另外有看到這台，但不知道售價？？？
http://www.kingsang.com.tw/ch/product_b1.html KSD-13
看它有90KG 應該是不便宜的東西…
幫忙多比較這台 http://goods.ruten.com.tw/item/show?21203221663435 ^^
◆ From: 118.170.202.171
目前考慮這台 http://goods.ruten.com.tw/item/show?21203234609990
有這台用戶可以分享一下嗎？
另外有看到這台，但不知道售價？？？
http://www.kingsang.com.tw/ch/product_b1.html KSD-13
看它有90KG 應該是不便宜的東西…
幫忙多比較這台 http://goods.ruten.com.tw/item/show?21203221663435 ^^
◆ From: 118.170.202.171
推 UntiedDragon:這種小台的我覺得也沒有很穩... 04/02 09:26
→ KarlJhan:會比電鑽固定架穩嗎？ 04/02 09:42
→ babytsai:床的話~桌上鑽床跟這角度架我都有使用過~ 04/02 09:48
→ KarlJhan:我是鑽鋁、鐵，這也ok嗎？它的底座是金屬還是其它材質？ 04/02 09:54
→ babytsai:底是塑鋼~金屬要鑽的準鑽頭要利轉速要慢底座要固定的牢 04/02 11:15
→ babytsai:鑽孔的時候加點潤滑油在鑽孔處會更好鑽 04/02 11:16
→ babytsai:如果你要做的東西不大建議用鑽床省力又精準 04/02 11:18
※ 編輯: KarlJhan 來自: 118.170.202.171 (04/02 11:59) 推 abelian:鋁還好 沒有很硬. 鐵就比較硬. 我曾經拿一根螺絲 在裡面 04/03 05:00
→ abelian:鑽洞. 大概 1.5mm x 2cm. 轉速要低 油一定不能少 慢慢壓 04/03 05:02
→ bonjovi31:要鑽很垂直是很困難的，鑽頭也是影響很大喔 04/05 14:53
Tags:
木工
All Comments
By Jake
at 2012-04-05T15:18
at 2012-04-05T15:18
By Cara
at 2012-04-07T22:31
at 2012-04-07T22:31
By Annie
at 2012-04-11T15:14
at 2012-04-11T15:14
By Selena
at 2012-04-13T12:58
at 2012-04-13T12:58
By George
at 2012-04-17T07:18
at 2012-04-17T07:18
By Kama
at 2012-04-17T12:43
at 2012-04-17T12:43
By Elma
at 2012-04-18T04:43
at 2012-04-18T04:43
By Daph Bay
at 2012-04-21T13:12
at 2012-04-21T13:12
By Ida
at 2012-04-22T08:14
at 2012-04-22T08:14
By Elizabeth
at 2012-04-25T05:23
at 2012-04-25T05:23
By Callum
at 2012-04-26T01:54
at 2012-04-26T01:54
Related Posts
請問木湯匙所需的工具
By Frederica
at 2012-03-28T12:27
at 2012-03-28T12:27
嗯......我又做了支髮簪
By Kelly
at 2012-03-27T23:11
at 2012-03-27T23:11
嗯......我做了名片夾
By Sarah
at 2012-03-27T18:44
at 2012-03-27T18:44
嗯......我做了名片夾
By Ethan
at 2012-03-26T22:33
at 2012-03-26T22:33
請問哪裡可以學木工?
By Yuri
at 2012-03-26T05:44
at 2012-03-26T05:44